Manufactured in Ontario

TotalSeal UltraSlim Series Vinyl Windows

The TotalSeal UltraSlim Series is a 4 9/16-inch frame depth vinyl window with an ultra-slim 2 ⅞-inch visible profile, built for homeowners across Toronto and the Greater Toronto Area who want a clean, modern look with the largest possible glass area. It uses multi-chamber uPVC profiles with fusion-welded corners, a concealed gasket system, and a TotalSeal warm-edge spacer as standard. 

Modern Minimalist Design with Maximum Glass

Every UltraSlim unit ships with a lifetime warranty and meets ENERGY STAR™ certified requirements for Canadian climate zones. If your current windows have thick, dated frames that block daylight and shrink your view, the UltraSlim Series is the answer. The 2 ⅞-inch frame width is well below the industry average for vinyl, which means more glass, more light, and a sharper exterior line. Meanwhile, the 4 9/16-inch depth gives room for advanced insulation chambers, optional foam fill, and a full 1-inch sealed glass unit.

Features

UltraSlim Series at a Glance

Energy Star

ENERGY STAR™ certified for Canadian climate zones

CSA

Tested to CSA A440.2-19 and NAFS (AAMA / WDMA / CSA 101 / I.S.2 / A440)

1

Frame material: Multi-chamber virgin uPVC with UV stabilisers and impact modifiers

Frame depth: 4 9/16 inches, suited for new construction, deep-wall retrofits, and full-frame replacement openings.

Corners: Fusion-welded at 45 degrees for a seamless joint

Sealed unit thickness: 1 inch, approximately 25 mm

5

Spacer: Warm-edge spacer system, thermal conductivity of 0.17 W/(m·K)

6

Weatherstripping: Concealed gasket system with rubber seals

7

Gas fill:
97% argon standard

8

Glazing: Double-glazed standard; triple-glazed optional

LoĒ 180
LoĒ 272
LoĒ 366
LoĒ i89

Low-E coating: Cardinal LoĒ-180 or LoĒ-272 standard. Optional LoĒ-366 and interior i89 coating.

Frame Thickness:

2 ⅞ inches — an ultra-slim visible profile that puts glass front and centre

Locking:

TotalSeal multi-point locking system with Roto Frank Ferco hardware and reinforced strike plates

Operator:

Encore die-cast zinc operator with E-Gard® coating and snap-fit cover for casement / awning types

Air Tightness:

A3 NAFS rating limits air leakage to ≤0.5 L/s·m² during testing

Water Penetration:

B7 rating indicates resistance to water entry at 700 Pa

Wind Load:

C5 rating confirms structural resistance at a test pressure of 4,500 Pa

Forced Entry:

F20 rating indicates resistance to defined forced-entry test conditions

Condenstaion Resistance:

Temperature Index (I) of 67 reflects resistance to interior condensation

Foam Filled:

Optional, with Ultra Low-E Foil reflective insulation available

Screen:

FlexScreen® compatible — tension-based retractable screen with no visible hardware

Warranty:

Lifetime, covering frame, glass, hardware, and installation

 

 

UltraSlim Series

Why the Ultra-Slim
2 ⅞-Inch Profile Matters

More Visible Glass Area than Standard Vinyl Frames

The average vinyl window frame in Canada is roughly 3 ¼ to 3 ½ inches wide. The UltraSlim profile is 2 ⅞ inches — about 15-20% narrower than a typical vinyl frame. On a standard 36×60-inch window, that difference adds several square inches of glass per unit. Across a full house of 15 to 20 windows, the extra daylight is noticeable from the first morning after installation.

Operator

A Flat, Modern Exterior Line with no Visible Gasket

Traditional vinyl windows show a rubber gasket bead around the sash-to-frame junction. The UltraSlim Series uses a concealed gasket system — the rubber seal tucks behind the frame profile, creating an unbroken, flat surface. The visual result is closer to an aluminium curtain wall or a European tilt-and-turn window, but with the insulating properties of vinyl. If your home leans toward contemporary or mid-century design, this is the window that matches the architecture rather than fighting it.

Sealed Unit Thickness

Deeper Frame Depth for Higher-Performance Insulation

At 4-9/16 inches deep, the UltraSlim frame is deeper than a standard 3 ¼-inch retrofit profile. That extra depth is not wasted space. It allows for more internal insulation chambers, room for optional foam fill, and a full 1-inch sealed glass unit instead of the 13/16-inch unit found in slimmer frames. A deeper frame also means a wider thermal break between the interior and exterior faces — and in a Toronto January, that thermal break is the difference between a warm sill and a cold one.

Materials

Frame Construction and Materials

The UltraSlim frame is extruded from virgin uPVC compound mixed with UV stabilisers and impact modifiers. These additives keep the vinyl from yellowing, chalking, or turning brittle after years of Ontario’s freeze-thaw cycles and harsh summer sun. The frame profile is designed as an ultra-flat, flush surface — unlike traditional bevelled or contoured vinyl profiles — which gives the window its distinctive contemporary appearance.

Internal Chambers and Optional Foam Fill

The standard double-glazed IGU uses two panes of glass separated by the Edgetech Super Spacer, with the cavity filled with argon gas. A Low-E coating — either Cardinal LoĒ-180 or LoĒ-272 — is applied to one interior glass surface (typically surface 2 or 3). This coating is a microscopic metallic layer that reflects long-wave infrared heat back into the room during winter and blocks solar heat gain in summer.

Fusion-Welded Corners

Every corner joint is fusion-welded at 45 degrees rather than screwed or glued. During fabrication, the cut ends of each profile piece are heated past their melting point and pressed together under controlled pressure. The result is a single continuous piece of vinyl at each corner — no gaps, no fastener holes, and no paths for water or air to get through. Fusion welding creates a molecular-level bond that is stronger than the vinyl itself, and these joints will not loosen over decades of thermal cycling in the Canadian climate.

Sash Construction

The sash — the moveable or fixed inner frame that holds the glass — is built from the same uPVC material, with its own set of internal chambers for additional insulation. Sash stiles (vertical sides) and sash rails (horizontal top and bottom pieces) are also fusion-welded for a sealed, rigid unit. Because the sash profile is designed to match the ultra-flat aesthetic of the frame, the entire window reads as a single clean plane of glass when viewed from inside or outside.

Structural Reinforcement

Because slim profiles can sacrifice rigidity, the UltraSlim Series includes strategic internal galvanised steel reinforcement plates (1.0 mm thickness) in load-bearing sections. Steel placement is determined by computational load analysis to make sure even large window units stay square and operate smoothly over their full lifespan. Performance ratings exceed NAFS requirements for structural integrity.

Glass Units

Insulated Glass Unit Options

The sealed glass unit — or IGU (insulated glass unit) — is where most of a window’s thermal performance lives. The UltraSlim Series accepts a full 1-inch (approximately 25 mm) sealed unit, which is thicker than the 13/16-inch unit used in standard retrofit frames. That extra thickness allows for wider gas-filled cavities and better overall insulation.

Double Pane Glass Unit

Double-Glazed IGU

The standard double-glazed IGU uses two panes of glass separated by the TotalSeal warm-edge spacer, with the cavity filled with 97% argon gas. A Low-E coating — either Cardinal LoĒ-180 or LoĒ-272 — is applied to one interior glass surface. This coating is a microscopic metallic layer that reflects long-wave infrared heat back into the room during winter and limits solar heat gain in summer.

Triple-pane IGU

Triple-Glazed IGU

For homeowners who want the highest insulation possible, the optional triple-glazed IGU adds a third pane of glass and a second gas-filled cavity. Triple glazing pushes the U-factor below 1.0 W/(m²K) — territory where interior glass surfaces stay warm to the touch even on the coldest January nights. The result is less condensation along the edges, quieter rooms, and noticeably lower heating bills through a Toronto winter.
Laminated IGU

Laminated Glass Option

Where security or sound control is a priority, the UltraSlim Series also offers a laminated glass option. The laminated IGU achieves a U-factor of 0.26 Btu/(h·ft²·°F) and blocks up to 99% of UV radiation, while raising the sound transmission class to STC 35 (compared to STC 29 for standard configurations). This makes it well suited for homes near highways, airports, or busy streets across the GTA — and the laminated interlayer holds the glass together if the pane is ever struck, adding a layer of forced-entry resistance.
Cardinal Glass

Seal Integrity

Cardinal Glass supplies the sealed units, and every IGU includes a dual-seal system: a primary polyisobutylene (PIB) seal for gas retention and a secondary silicone or polyurethane sealant for structural bonding. A desiccant-filled spacer bar absorbs any residual moisture trapped during assembly — preventing the foggy, clouded look that signals seal failure.

Warm Spacer

TotalSeal Warm-Edge Spacer — Why It Matters

The spacer bar sits between the panes of glass at the edges of the sealed unit. Traditional spacers are made from aluminium — a metal that conducts heat fast. That means the edges of your glass are always colder than the centre, leading to condensation, ice formation, and energy loss exactly where the glass meets the frame.

Warm-Edge

Low-Conductivity Warm-Edge Design

The UltraSlim Series uses the TotalSeal warm-edge spacer system, which has a thermal conductivity of just 0.17 W/(m·K)  — a fraction of what aluminium spacers conduct. Because the spacer does not pull heat out of the glass edges the way metal does, the edges stay closer to the temperature of the glass centre. The practical result: less condensation on cold mornings, better argon retention inside the sealed unit, and a lower overall U-factor for the whole window assembly.

Durability

Durability Under Thermal Stress

The TotalSeal spacer flexes with temperature changes rather than fighting them. As the sealed unit expands in summer heat and contracts in winter cold, the spacer absorbs that movement without cracking the sealant bond. This flexibility is one of the main reasons warm-edge spacers outperform rigid aluminium bars in long-term gas retention and seal durability — especially in climates like Ontario’s, where a single year can bring temperature swings of 60°C or more.

Energy Efficiency

Energy Performance and Certifications

The UltraSlim Series meets the requirements for ENERGY STAR™ certification under the current Canadian technical specification administered by Natural Resources Canada (NRCan). To earn this label, a window must hit specific thresholds for U-factor, solar heat gain coefficient (SHGC), and energy rating (ER) based on the climate zone where it will be installed. Here is what those numbers mean in plain terms:

U-Factor

U-factor measures how fast heat escapes through the entire window — glass, frame, spacer, and all. It is rated in W/(m²·K) or Btu/(h·ft²·°F) in US/Canadian industry specs). Lower is better. A double-glazed UltraSlim casement with LoĒ-272 glass typically falls around 1.59 W/(m²·K), while the LoĒ-366 plus i89 configuration drops to roughly 1.14 W/(m²·K) — and triple glazing pushes below 1.0 W/(m²·K).

Solar Heat Gain Coefficient

SHGC measures how much of the sun's heat passes through the glass. It is rated on a scale from 0 to 1. In Ontario, you generally want a moderate SHGC — enough to gain free solar heat in winter, but not so much that rooms overheat in summer. The UltraSlim Series offers SHGC values from 0.69 (LoĒ-180, maximum solar gain) down to 0.27 (LoĒ-366/i89, maximum solar control), so you can pick the right coating for each window orientation.

Energy Rating

ER is a Canadian-specific metric that balances heat loss (U-factor), passive solar gain (SHGC), and air leakage into a single number. A higher ER means the window performs better overall for the Canadian climate. The UltraSlim Series meets or exceeds the ER thresholds for all Ontario climate zones.

Air Tightness

Air Leakage

Air is tested in litres per second per square metre (L/s/m²) at a standard pressure. Lower is better. Under the NAFS (North American Fenestration Standard, AAMA/WDMA/CSA 101/I.S.2/A440), windows are classified by their air tightness from A1 (least tight) to A3 (most tight). The UltraSlim Series achieves A3 rating — the highest tier — at ≤0.5 L/s·m² across operable window types.

Weatherstripping

Water Penetration

Beyond air, the UltraSlim Series is also tested for water penetration resistance (B7 rated at 700 Pa), wind load resistance (C5 rated to withstand 4,500 Pa), and forced entry resistance (F20 rated). The condensation resistance temperature index (I) is 67, which means interior glass and frame surfaces stay warm enough to prevent moisture buildup in typical Canadian heating-season conditions.

Energy Star

In addition to ENERGY STAR™ certification, the UltraSlim Series is tested to CAN/CSA-A440 for fenestration energy performance and evaluated to the NAFS for structural integrity, water penetration resistance, and forced entry resistance. Independent third-party testing labs verify every claim.

Security

TotalSeal Multi-Point Locking System

Security and air tightness go hand in hand. The UltraSlim Series uses a multi-point locking mechanism with lock points set at strategic intervals — typically 16 inches apart — along the sash perimeter. The hardware is supplied by Roto Frank Ferco, a German manufacturer of window fittings, and uses 300-series stainless steel components built to last in coastal and urban Canadian environments.

Reinforced Strike Plate

Each lock point engages a reinforced strike plate on the frame side with a 0.354-inch throw distance. When you close the handle, the lock points pull the sash tightly and evenly against the concealed gasket around the full perimeter. This distributed pressure creates a consistent seal — no sagging corners, no gaps, no rattling. The compression is adjustable by ±0.08 inches, so installers can fine-tune the seal to each specific opening.

TotalSeal Corner Drive

Integrated Corner Drive

The integrated corner drive sits approximately 3 inches from each corner of the sash frame. This placement reinforces the corners — traditionally the weakest points of any window — against both forced entry and air leakage. It absorbs and distributes stress across the corner junction rather than concentrating it at a single lock point in the centre of the rail. Combined with the F20 forced entry rating, the UltraSlim locking system meets or exceeds residential security standards across Ontario.

Truth Operator Locking System

Encore Operator

The Encore operator (the handle mechanism on casement and awning windows) features a die-cast zinc body with E-Gard® coating for corrosion resistance. It runs on an 8:1 gear ratio for smooth, low-effort operation and offers a full 170-degree folding handle clearance. The snap-fit cover is made from engineered polymer — it folds flat against the frame when not in use, stays out of the way of blinds and curtains, and keeps the gear mechanism clean. The operator is tested to 20,000 cycles, which works out to more than 50 years of typical use.

Air Leakage

Weatherstripping and Air Sealing

The UltraSlim Series uses a concealed gasket system — one of the defining features of the line. Instead of visible rubber beads pressed into grooves on the face of the frame, the seals are hidden behind the frame profile. This keeps the flat, modern appearance intact while still providing full-perimeter sealing against air and water.

Layered Seals

Layered Seals

Multiple sealing layers run along the full contact area between the sash and the frame. The hidden rubber gaskets compress when the sash is locked into position, and the multi-point locking system holds them under even, consistent pressure. Even as the vinyl frame expands and contracts with temperature shifts, at least one seal remains compressed and in contact at all times. The weatherstripping works together with the multi-point lock to maintain A3 air tightness.

Weep Holes

Weep Holes & Covers

Weep holes in the sill track allow any water that enters the track area to drain to the exterior. Small weep hole covers prevent insects from entering while still allowing drainage. This is particularly important in the GTA, where driving rain and snowmelt can push water into the frame track during spring thaws and late-autumn storms.

FlexScreen

FlexScreen® Integration

The UltraSlim Series is engineered from the factory to accept FlexScreen® — a tension-based retractable screen system that does away with the bulky aluminium screen frames found on conventional windows.

FlexScreen

How FlexScreen Works

FlexScreen uses a high-tensile, phosphate-coated spring steel frame just 0.175 inches thick, wrapped in PVC-coated polyester mesh (18×16 mesh count per square inch). It pops into a proprietary retention channel along the interior of the window frame and holds itself in place by tension alone — no clips, no pins, no visible hardware. The screen flexes to fit the opening, so it can be removed in seconds for cleaning and stored flat when not in use.

Why it Suits the UltraSlim Design

A traditional aluminium screen frame adds visual clutter and blocks light — which defeats the purpose of a slim-profile window. FlexScreen is nearly invisible from inside and outside the home, so the full glass area and clean frame lines are preserved. For homeowners investing in a contemporary aesthetic, this screen system is a natural match.

Window Styles

Available Window Styles in the UltraSlim Series

The 4-9/16-inch UltraSlim frame accommodates every common residential window type:

Configurations

Glazing Bead, Grilles, and Interior Finish Options

Glazing Beads
The glass is held in the sash by a snap-in glazing bead — a vinyl strip that clicks into a channel in the sash frame. This allows the sealed unit to be replaced without removing the entire sash or frame, which simplifies service if a seal ever fails.
For homeowners who want a traditional divided-lite look, internal grilles (also called muntins or GBG — grilles between glass) are available in 5/16-inch, 5/8-inch, and 1-inch widths. These flat or contoured bars sit inside the sealed unit, so they never need cleaning and do not interrupt the thermal performance of the IGU. Simulated divided lite (SDL) and true divided lite (TDL) options are also offered.
The UltraSlim Series is available in standard uPVC white, beige, and bronze, along with 14 acrylic overlay finishes and custom paint to any RAL colour code. Hardware finishes include white, black, satin nickel, oil-rubbed bronze, brushed chrome, and antique brass — so the window can be matched to any interior style, from warm traditional to cool industrial.
Book a free in-home estimate
Discuss your project with one of our experts and receive a personalized quote.

Process

How the Replacement and Installation Process Works

TotalSeal handles window installation as a full-service project — no subcontractors, no middlemen:

Step 1: Free In-Home Consultation

A consultant visits your home, measures every opening, and assesses your property type — detached house, townhouse, semi-detached, or condominium. They discuss glass options (double or triple), hardware finishes, foam fill, and any custom sizing needed for non-standard openings. Because the UltraSlim frame is 4-9/16 inches deep, the consultant will verify that your wall depth and opening dimensions are a fit — and recommend the right installation method (full-frame replacement or insert) based on your home's construction.

Step 2: Custom Manufacturing

Your order goes into production at the GTA manufacturing facility, where automated Pro-Line machinery cuts, welds, and assembles each window to your exact measurements. The UltraSlim Series runs on the same high-capacity production line that handles up to 150 units per day across all product lines, so lead times stay short even during peak season.

Step 3: Professional Installation

On installation day, certified in-house crews remove your old windows, prepare the rough opening, set the new UltraSlim unit, shim and level it, apply foam insulation and caulking, and install interior trim. The 4-9/16-inch frame depth requires precise shimming to ensure the window sits plumb and square — a job for experienced installers, not general contractors. The result is an airtight, watertight, building-code-compliant installation with no mess left behind.
Get a Free Quote
Get a Free Quote for the UltraSlim Series
Ready to upgrade to a modern, slim-profile window with more glass and less frame? Contact us for a free, no-obligation in-home consultation. Or visit the TotalSeal showroom to see the UltraSlim Series in person and compare it with the Classic Series side by side.

By submitting this form, you agree to our Terms and Conditions.

Get a free quote
Schedule an in-home estimate

By submitting this form, you agree to our Terms and Conditions.

Get a free quote
Schedule an in-home estimate

By submitting this form, you agree to our Terms and Conditions.